Preface: This article covers what worn belts may look like on your Nova series machine. Odometer Reading: Using Lightburn's "Get Controller information" we can take a peak at the odometer of the machine. The Nova 51 has over 5000 hours of movement ...
Preface: This article covers how to flash the Ruida DSP firmware using RDworksV8 over a USB Connection. You will need to install and establish the connection prior to doing a firmware flash, that is not covered in this article. Quick Start Video: ...
Preface: This article covers How To align your laser beam in a 3 mirror gantry based Nova laser. Here are some quickstart videos that will cover 90% of the situations. They do not contain every last iota of detail but should be enough to get most ...
The small X axis belt can sometimes become 'noisy' enough to warrant replacing. This is often mistaken for bearing noise. This noise will sounds like squeaking, growling, like a bearing. But the bearings are likely okay and no lubrication is required ...
This guide will show you the steps needed to replace the stack light on a Nova series machine. Some variations in components may exist depending on vintage. What you will need to complete this job: -20 minutes -Small flat head screw driver -3mm Allen ...
This article covers how to replace the 24V Power supply that powers the controls for your NOVA machine. Note that this was done on a NOVA35. Larger Machines like the NOVA63 will have this Power Supply by it self not hidden by the 36V power supply. ...
This article covers how to replace the 36V Power supply that powers the drivers for your NOVA machine You will need: -30 minutes -Phillips screw driver with standard length -Voltmeter (How To Use A Multimeter) -Camera -Replacement Meanwell LRS-350-36 ...
Preface: This guide will walk you through the physical replacement of the controller. Be sure to read it completely and understand that the machine will not react like normal until the controller is configured correctly. If you attempt to use ...
We have gotten reports of the mirror optic mounts being stuck or cross-threaded. This is usually rectified by using the included pliers to achieve more positive engagement and more leverage to remove the ring. NOTE: Never use the pliers to install or ...
Preface: This article will cover Laser Power Supply replacement on Thunder Laser Nova series machines. Before we begin: The LPSU outputs somewhere around 30,000 VDC and can store a charge so always heed the big red wires and connectors. They are ...
Start off by scoring at 100mm square on a flat piece of material, then proceed with the adjustments of the bearings and couplers as needed. You may need to score the square again after making an adjustment to recheck and adjust. The diagonal lines on ...
This documentation is specific to the Thunder Nova series stock 2" (50.8mm) focal length lens assembly. We have typically used 6mm (1/4") as the reference for focus but it can vary. Thunder Laser actually specifies the focal distance as 4.5mm~6.5mm: ...
This procedure is how to use the Channel 2 output in place of the Ch1 output on your Laser Machine. Step 1: Backup Machine Settings to computer Machine Settings in Lightburn (Must be connected to the machine). From Lightburn goto Edit>Machine ...
Preface: This article covers how to easily calibrate an Axis in Lightburn using the built in wizard Make sure you back up the Laser Machine Settings before you edit them: Backing Up Machine and LightBurn Settings Tools you will need: Accurate ...
Preface: This article covers two methods on how to adjust bearing tension. Both methods are done with the power off to the machine. Your machine may have 2 set screws for the bearing. Be sure to loosen and tighten both for adjustments. Method 1: ...
The blades can become dislodged, jammed, etc... during shipment. When this happens, the frames can spread from a jammed blade and cause tolerance issues and other blades can fall out It's a good idea to remove the honeycomb: Removing the Honeycomb ...
Since LightBurn 1.2.00, a function has been added to the device settings in LightBurn to define a time delay for the start and end of a job. Click the wrench/screwdriver icon to open the pop-up Device Settings window. Adjust your start delay to ...
Preface: This article covers how to Load the Material Library that you download into Lightburn How to Video: Complete Guide: Things to note: 1. The Library File that you download will always need to exist. Do not Delete it. Lightburn will reference ...
Preface: This article covers how to clean your optics on your Thunder Nova Series Laser Lenses Explained Quick Start Video: (Video Credit: Robert Kofoed of Computer Creationz) Complete Guide: Before you Begin: Cleaning your optics can help keep your ...
*This information is provided “AS IS” to provide a starting point. It is always a good idea to run tests on each substrate and update the library as necessary. The Official Thunder Material Library PDF below and the precompiled LightBurn library file ...
Preface: This article covers various cuttings speeds for different materials based on testing. Your specific results will rely on having a similar material and setup. Results are not guaranteed. Parameters Chart: Find the material you want to cut in ...
If you are a Thunder Laser USA client and still need Technical Support after exhausting the resources in the Knowledge Base, simply email support@thunderlaserusa.com and the Technical Support Team will promptly assist you!