DC 80 & 100W Power Output Variances By Firmware Level

DC 80 & 100W Power Output Variances By Firmware Level

MORE ON MACHINE DIFFERENCES BY FIRMWARE HERE:


V8.07.59 or less


C100-SPT CO2 Glass tubeC90-SPT CO2 Glass tube
power settingcurrent(mA)power of tube(watt)current(mA)power of tube(watt)
1%0000
2%0000
3%0000
4%0000
5%0000
6%0000
7%0000
8%101.31.7
9%2.43.42.94.4
10%2.95.33.67.5
15%4114.213.1
20%4.516.34.219.2
25%4.618.84.323
30%7.145.6845.6
35%8.754.69.652.8
40%10.563.311.459.3
45%12.672.71673.5
50%14.379.819.181.4
55%18.394.321.388.3
60%20.8102.32390.4
65%22.6107.824.594.8
70%24.2112.326.198
75%25.9116.128100.2
80%27.7119.830102.7
85%29.4120.231.2101.4
90%30.6123.131.4101.8
95%31.4123.231.6102.2
99%31121.731.6101.6


1.MYJG100-110V power supply;the max current for 80/100w laser tube should be under 25mA

2.Machine setting(Vendor setting) of laser:Min power 1%;Max power 99%

3.The firmware of DSP is RDC644XG-V8.07.59 or less,user can set power form Min power~Max power of machine setting

4.Power setting over 70% is too high for the current,so we limit the machine setting of laser:Min power 1%;Max power 70%.User can set power from 1%~70%,actually only around 7%~70%.


V8.07.63 or higher


C100-SPT CO2 Glass tubeC90-SPT CO2 Glass tube
power settingcurrent(mA)power of tube(watt)current(mA)power of tube(watt)
1%0000
2%0012.6
3%23.924.3
4%23.437
5%35.438.7
6%35.539.6
7%36.1310.2
8%36310.4
9%36.1310.7
10%36.7311.1
15%415.5421.5
20%518.5539.6
25%520.5646.1
30%642.7852
35%749.2956.5
40%855.21059.2
45%961.11265.4
50%1167.81573
55%1275.81676.7
60%1483.81884.1
65%16891988.3
70%1893.32189
75%1997.22284.7
80%20103.82393.3
85%22106.92496.3
90%22107.52598.1
95%22106.426100.4
99%22106.627100


1.MYJG100-110V power supply;the max current for 80/100w laser tube should be under 25mA                        

2.Machine setting(Vendor setting) of laser:Min power 7%;Max power 70%                        

3.The firmware of DSP is RDC644XG-V8.07.63 or high,user can set power form 1~99%,1% is equal with 7%,99% is equal with 70% 


MORE ON MACHINE DIFFERENCES BY FIRMWARE HERE:


Nova Series Firmware

END


    If you are a Thunder Laser USA client and still need Technical Support after exhausting the resources in the Knowledge Base, simply email support@thunderlaserusa.com and the Technical Support Team will promptly assist you!